350-401 | ExamData

Question#151

Which device makes the decision for a wireless client to roam?

A. wireless client
B. wireless LAN controller
C. access point
D. WCS location server

Discover Answer

A
Reference:
https://documentation.meraki.com/MR/WiFi_Basics_and_Best_Practices/Client_roaming_and_connectivity_decisions_explained

Question#152

An engineer configures GigabitEthernet 0/1 for VRRP group 115. The router must assume the primary role when it has the highest priority in the group.
Which command set is required to complete this task?
interface GigabitEthernet0/1
ip address 10.10.10.2 255.255.255.0
vrrp 115 ip 10.10.10.1
vrrp 115 authentication 407441579

A. Router(config if)# vrrp 115 track 1 decrement 100 Router(config-if)# vrrp 115 preempt
B. Router(config-if)# vrrp 115 priority 100
C. Router(config-if)# vrrp 115 track 1 decrement 10 Router(config-if)# vrrp 115 preempt
D. Router(config-if)# standby 115 priority 100 Router(config-if)# standby 115 preempt

Discover Answer

B
Reference:
https://www.cisco.com/assets/sol/sb/Switches_Emulators_v2_3_5_xx/help/350_550/index.html#page/tesla_350_550_olh/ts_vrrp_18_09.html

Question#153

How is MSDP used to interconnect multiple PIM-SM domains?

A. MSDP allows a rendezvous point to dynamically discover active sources outside of its domain.
B. MSDP SA request messages are used to request a list of active sources for a specific group.
C. MSDP depends on BGP or multiprotocol BGP for interdomain operation.
D. MSDP messages are used to advertise active sources in a domain.

Discover Answer

C
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-16/imc-pim-xe-16-book/imc-msdp-im-pim-sim.html

Question#154

If the noise floor is -90 dBm and the wireless client is receiving a signal of גˆ’75 dBm, what is the SNR?

A. 15
B. 1.2
C. גˆ’165
D. .83

Discover Answer

A
Signal Strength גˆ’ Noise floor = SNR

Question#155

Refer to the exhibit.

The EtherChannel between SW2 and SW3 is not operational. Which action resolves this issue?

A. Configure the channel-group mode on SW3 Gi0/0 and Gi0/1 to active.
B. Configure the mode on SW2 Gi0/0 to trunk.
C. Configure the channel-group mode on SW2 Gi0/0 and Gi0/1 to on.
D. Configure the mode on SW2 Gi0/1 to access.

Discover Answer

B

Question#156

Refer to the exhibit.

Which action completes the configuration to achieve a dynamic continuous mapped NAT for all users?

A. Reconfigure the pool to use the 192.168.1.0 address range.
B. Configure a match-host type NAT pool.
C. Increase the NAT pool size to support 254 usable addresses.
D. Configure a one-to-one type NAT pool.

Discover Answer

C

Question#157

How does EIGRP differ from OSPF?

A. EIGRP is more prone to routing loops than OSPF.
B. EIGRP uses more CPU and memory than OSPF.
C. EIGRP has a full map of the topology, and OSPF only knows directly connected neighbors.
D. EIGRP supports equal or unequal path cost, and OSPF supports only equal path cost.

Discover Answer

D
Reference:
https://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/13677-19.html

Question#158

Which AP mode allows a supported AP to function like a WLAN client would, associating and identifying client connectivity issues?

A. client mode
B. SE-connect mode
C. sensor mode
D. sniffer mode

Discover Answer

C
Reference:
https://content.cisco.com/chapter.sjs?uri=/searchable/chapter/content/dam/en/us/td/docs/wireless/controller/technotes/8-5/ b_Cisco_Aironet_Sensor_Deployment_Guide.html.xml

Question#159

A client device roams between wireless LAN controllers that are mobility peers. Both controllers have dynamic interfaces on the same client VLAN. Which type of roam is described?

A. intra-VLAN
B. inter-controller
C. intra-controller
D. inter-subnet

Discover Answer

B
Reference:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/config-guide/b_wl_16_10_cg/mobility.html

Question#160

Which component does Cisco Threat Defense use to measure bandwidth, application performance, and utilization?

A. TrustSec
B. Advanced Malware Protection for Endpoints
C. NetFlow
D. Cisco Umbrella

Discover Answer

C
Reference:
https://www.cisco.com/c/dam/en/us/solutions/collateral/enterprise/design-zone-security/ctd-first-look-design-guide.pdf page 8