Exams > Cisco > 350-401: Implementing Cisco Enterprise Network Core Technologies (ENCOR)
350-401: Implementing Cisco Enterprise Network Core Technologies (ENCOR)
Page 2 out of 62 pages Questions 11-20 out of 614 questions
Question#11

What is required for a virtual machine to run?

  • A. a Type 1 hypervisor and a host operating system
  • B. a hypervisor and physical server hardware
  • C. only a Type 1 hypervisor
  • D. only a Type 2 hypervisor
Discover Answer Hide Answer

B

Question#12

Which entity is a Type 1 hypervisor?

  • A. Oracle VM VirtualBox
  • B. Citrix XenServer
  • C. VMware server
  • D. Microsoft Virtual PC
Discover Answer Hide Answer

B

Question#13

What are two benefits of virtual switching when compared to hardware switching? (Choose two.)

  • A. increased MTU size
  • B. VM-level isolation
  • C. extended 802.1Q VLAN range
  • D. hardware independence
  • E. increased flexibility
Discover Answer Hide Answer

DE

Question#14

What is a characteristic of a virtual machine?

  • A. It must run the same operating system as its host.
  • B. It is deployable without a hypervisor to host it.
  • C. It must be aware of other virtual machines, in order to allocate physical resources for them.
  • D. It relies on hypervisors to allocate computing resources for it.
Discover Answer Hide Answer

D

Question#15

Which LISP component is required for a LISP site to communicate with a non-LISP site?

  • A. Proxy ITR
  • B. ITR
  • C. ETR
  • D. Proxy ETR
Discover Answer Hide Answer

D

Question#16

Which two components are supported by LISP? (Choose two.)

  • A. proxy ETR
  • B. egress tunnel router
  • C. route reflector
  • D. HMAC algorithm
  • E. spoke
Discover Answer Hide Answer

AB

Question#17

What is the function of a VTEP in VXLAN?

  • A. provide the routing underlay and overlay for VXLAN headers
  • B. dynamically discover the location of end hosts in a VXLAN fabric
  • C. encapsulate and de-encapsulate traffic into and out of the VXLAN fabric
  • D. statically point to end host locations of the VXLAN fabric
Discover Answer Hide Answer

C

Question#18


Refer to the exhibit. Which configuration must be applied to R1 to enable R1 to reach the server at 172.16.0.1?

  • A. interface Ethernet0/0 ip address 172.16.0.7 255.255.0.0 router ospf 44 vrf bank network 172.16.0.0 255.255.0.0
  • B. interface Ethernet0/0 vrf forwarding hotel ip address 172.16.0.7 255.255.0.0 router ospf 44 vrf Hotel network 172.16.0.0 0.0.255.255 area 0
  • C. interface Ethernet0/0 vrf forwarding bank ip address 172.16.0.7 255.255.0.0 router ospf 44 vrf bank network 172.16.0.0 0.0.255.255 area 0
  • D. interface Ethernet0/0 ip address 172.16.0.7 255.255.0.0 router ospf 44 vrf hotel network 172.16.0.0 255.255.0.0
Discover Answer Hide Answer

C

Question#19


Refer to the exhibit. Which configuration allows Customer2 hosts to access the FTP server of Customer1 that has the IP address of 192.168.1.200?

  • A. ip route vrf Customer1 172.16.1.0 255.255.255.0 172.16.1.1 global ip route vrf Customer2 192.168.1.200 255.255.255.255 192.168.1.1 global ip route 192.168.1.0 255.255.255.0 Vlan10 ip route 172.16.1.0 255.255.255.0 Vlan20
  • B. ip route vrf Customer1 172.16.1.1 255.255.255.255 172.16.1.1 global ip route vrf Customer2 192.168.1.200 255.255.255.0 192.168.1.1 global ip route 192.168.1.0 255.255.255.0 Vlan10 ip route 172.16.1.0 255.255.255.0 Vlan20
  • C. ip route vrf Customer1 172.16.1.0 255.255.255.0 172.16.1.1 Customer2 ip route vrf Customer2 192.168.1.200 255.255.255.255 192.168.1.1 Customer1
  • D. ip route vrf Customer1 172.16.1.0 255.255.255.0 172.16.1.1 Customer1 ip route vrf Customer2 192.168.1.200 255.255.255.255 192.168.1.1 Customer2
Discover Answer Hide Answer

A

Question#20


Refer to the exhibit. A network engineer configures a new GRE tunnel and enters the show run command. What does the output verify?

  • A. The tunnel keepalive is configured incorrectly because they must match on both sites.
  • B. The tunnel destination will be known via the tunnel interface.
  • C. The tunnel will be established and work as expected.
  • D. The default MTU of the tunnel interface is 1500 bytes.
Discover Answer Hide Answer

B

chevron rightPrevious Nextchevron right