Exams > Cisco > 200-301: Cisco Certified Network Associate (CCNA)
200-301: Cisco Certified Network Associate (CCNA)
Page 16 out of 80 pages Questions 151-160 out of 791 questions
Question#151

What are two benefits of using VTP in a switching environment? (Choose two.)

  • A. It allows switches to read frame tags.
  • B. It allows ports to be assigned to VLANs automatically.
  • C. It maintains VLAN consistency across a switched network.
  • D. It allows frames from multiple VLANs to use a single interface.
  • E. It allows VLAN information to be automatically propagated throughout the switching environment.
Discover Answer Hide Answer

CE

Question#152

Which three statements are typical characteristics of VLAN arrangements? (Choose three.)

  • A. A new switch has no VLANs configured.
  • B. Connectivity between VLANs requires a Layer 3 device.
  • C. VLANs typically decrease the number of collision domains.
  • D. Each VLAN uses a separate address space.
  • E. A switch maintains a separate bridging table for each VLAN.
  • F. VLANs cannot span multiple switches.
Discover Answer Hide Answer

BDE

Question#153

On a corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?

  • A. a router with subinterfaces configured on the physical interface that is connected to the switch
  • B. a router with an IP address on the physical interface connected to the switch
  • C. a switch with an access link that is configured between the switches
  • D. a switch with a trunk link that is configured between the switches
Discover Answer Hide Answer

A
Different VLANs can't communicate with each other, they can communicate with the help of Layer3 router. Hence, it is needed to connect a router to a switch, then make the sub-interface on the router to connect to the switch, establishing Trunking links to achieve communications of devices which belong to different VLANs.

Question#154

Which statement about LLDP is true?

  • A. It is a Cisco proprietary protocol.
  • B. It is configured in global configuration mode.
  • C. The LLDP update frequency is a fixed value.
  • D. It runs over the transport layer.
Discover Answer Hide Answer

B

Question#155

What is a function of Wireless LAN Controller?

  • A. register with a single access point that controls traffic between wired and wireless endpoints
  • B. use SSIDs to distinguish between wireless clients
  • C. send LWAPP packets to access points
  • D. monitor activity on wireless and wired LANs
Discover Answer Hide Answer

C
Lightweight APs (LAPs) is devices require no initial configuration. LAPs use the Lightweight Access Point Protocol (LWAPP) to communicate with a WLAN controller (WLC), as shown in the below figure. Controller-based APs are useful in situations where many APs are required in the network. As more APs are added, each AP is automatically configured and managed by the WLC.

Question#156

Which technology is used to improve web traffic performance by proxy caching?

  • A. WSA
  • B. Firepower
  • C. ASA
  • D. FireSIGHT
Discover Answer Hide Answer

A

Question#157

What criteria is used first during the root port selection process?

  • A. local port ID
  • B. lowest path cost to the toot bridge
  • C. lowest neighbor's bridge ID
  • D. lowest neighbor's port ID
Discover Answer Hide Answer

B

Question#158

Which statement about VLAN configuration is true?

  • A. The switch must be in VTP server or transparent mode before you can configure a VLAN
  • B. The switch must be in config-vlan mode before you configure an extended VLAN
  • C. Dynamic inter-VLAN routing is supported on VLAN2 through VLAN 4064
  • D. A switch in VTP transparent mode save the VLAN databases to the running configuration only
Discover Answer Hide Answer

A

Question#159

Refer to the exhibit. What two conclusions should be made about this configuration? (Choose two.)

  • A. The root port is FastEthernet 2/1
  • B. The designated port is FastEthernet 2/1
  • C. The spanning-tree mode is PVST+
  • D. This is a root bridge
  • E. The spanning-tree mode is Rapid PVST+
Discover Answer Hide Answer

AE

Question#160

A network engineer must create a diagram of a multivendor network. Which command must be configured on the Cisco devices so that the topology of the network is allowed to be mapped?

  • A. Device(config)#lldp run
  • B. Device(config)#cdp run
  • C. Device(config-if)#cdp enable
  • D. Device(config)#flow-sampler-map topology
Discover Answer Hide Answer

A

chevron rightPrevious Nextchevron right